Workbench stuck at level 3
for some reason even when i have 3 upgrades at the moment;
Chopping block
Tanning rack
and adze
(No obsidian, no tool shelf)
I am well into the iron age and i have had it upgraded to level 4 before. Rebuilding these upgrades or workbench does not level it up.
Any ideas?
Chopping block
Tanning rack
and adze
(No obsidian, no tool shelf)
I am well into the iron age and i have had it upgraded to level 4 before. Rebuilding these upgrades or workbench does not level it up.
Any ideas?
11:13 am, August 9, 2021
sneakyweazel replied to Workbench stuck at level 3 August 9, 2021 @ 9:04:54 am PDT
This is not KSP! No part clipping...
Well, except wood piles! Or maybe also rock formations... and chests and shelves, of course. Pretty much anything goes but my tanning rack will be by the fire
Well, except wood piles! Or maybe also rock formations... and chests and shelves, of course. Pretty much anything goes but my tanning rack will be by the fire
5:13 pm, August 9, 2021
0 comments
0 likes
Gunther Ultrabolt Novacrunch replied to Workbench stuck at level 3 August 9, 2021 @ 10:09:26 am PDT
I often will dig a large sub floor under my benches so that I can place all the knick knacks required to raise its level directly beneath it (and out of site).
5:13 pm, August 9, 2021
0 comments
0 likes
GunsForBucks replied to Workbench stuck at level 3 August 9, 2021 @ 5:21:43 am PDT
Upgrades need to be within a certain distance.
If "connected" you will see a dotted line light up.
Probably one of the parts is not properly associating with it.
Deconstruct the upgrades and replace them watching for connection line.
If "connected" you will see a dotted line light up.
Probably one of the parts is not properly associating with it.
Deconstruct the upgrades and replace them watching for connection line.
2:13 pm, August 9, 2021
0 comments
0 likes
sneakyweazel replied to Workbench stuck at level 3 August 9, 2021 @ 5:47:17 am PDT
Thank you all for the info and suggestions.
The tanning rack was few inches too far after reconstructing workbench just a bit closer to the wall
The tanning rack was few inches too far after reconstructing workbench just a bit closer to the wall
2:13 pm, August 9, 2021
0 comments
0 likes
Martin replied to Workbench stuck at level 3 August 9, 2021 @ 6:00:20 am PDT
You can "sink" the tanning rack into the wall and put some items under or above the work station to get a better more compact design.
2:13 pm, August 9, 2021
0 comments
0 likes
Cockpuncher replied to Workbench stuck at level 3 August 9, 2021 @ 2:50:00 am PDT
With 3 upgrades it should be level 4. Probably one of the items is too far away from the workbench to work properly.
11:13 am, August 9, 2021
0 comments
0 likes
[EASY] Caelib replied to Workbench stuck at level 3 August 9, 2021 @ 4:11:04 am PDT
With 3 upgrades it should be level 4. Probably one of the items is too far away from the workbench to work properly.
I agree ... this is likely to occur if you remove the workbench and re-place it. This is the only scenario where you might have disconnected upgrades.
11:13 am, August 9, 2021
0 comments
0 likes