Raise ground issues
I am trying to raise the ground for a project. but for some reason part of the ground wont be raised to the level of the rest.
I have read online that there is a limit of 8 meters from the map generated ground level.
Not sure if this is right or wrong...
However the part that has holes in it, is next to a small river, while i can raise the lowest ground level (river level) beond those holes. (about 1,5m higher).
Anyone got a sollution for this?
I have read online that there is a limit of 8 meters from the map generated ground level.
Not sure if this is right or wrong...
However the part that has holes in it, is next to a small river, while i can raise the lowest ground level (river level) beond those holes. (about 1,5m higher).
Anyone got a sollution for this?
5:13 pm, October 17, 2021
jonnin replied to Raise ground issues October 17, 2021 @ 10:51:39 am PDT
The solution depends on the cause.
- you can only raise (or dig) so far. So if the original ground was not level (it was not, unless you are building in an area smaller than 1 floor tile). then raise everything to the max will be ... just as uneven as the original.
in that case, you knock everything down to the lowest common level, or insert an extra stone floor tile or two in low spots.
other causes ... mostly see above...
- you can only raise (or dig) so far. So if the original ground was not level (it was not, unless you are building in an area smaller than 1 floor tile). then raise everything to the max will be ... just as uneven as the original.
in that case, you knock everything down to the lowest common level, or insert an extra stone floor tile or two in low spots.
other causes ... mostly see above...
8:13 pm, October 17, 2021
0 comments
0 likes
Lucidess replied to Raise ground issues October 17, 2021 @ 10:55:31 am PDT
Instance count: *cries*
8:13 pm, October 17, 2021
0 comments
0 likes
Mharr replied to Raise ground issues October 17, 2021 @ 12:18:58 pm PDT
How do you patch a hole with stonework?The stone blocks are fully 3d cuboids where most wooden pieces are effectively 2d cardboard cutouts. They're pretty easy to place embedded into the ground, especially the 2x2x1 flooring block.
The stonecutter does need two iron ingots so that's a swamp run but not necessarily a deep one - the larger ooze creatures drop iron ore, or you can find deposits in the steep slope where a swamp meets mountain.
8:13 pm, October 17, 2021
0 comments
0 likes
Mharr replied to Raise ground issues October 17, 2021 @ 8:02:40 am PDT
There's a delimiter mod https://www.nexusmods.com/valheim/mods/359 or you'll need to lower the entire thing, or patch the hole with stonework.
5:13 pm, October 17, 2021
0 comments
0 likes
Kruxed replied to Raise ground issues October 17, 2021 @ 8:51:39 am PDT
Sometimes a rock nearby will cause things like that
5:13 pm, October 17, 2021
0 comments
0 likes
Aimee replied to Raise ground issues October 17, 2021 @ 8:57:14 am PDT
Sometimes a rock nearby will cause things like thatWould removing the ground, to find this rock, and destroy it. Fix this problem?
There's a delimiter mod https://www.nexusmods.com/valheim/mods/359 or you'll need to lower the entire thing, or patch the hole with stonework.How do you patch a hole with stonework?
I dont quite have access to the stone cutter yet, but i could try and get it if that helps solve this problem.
5:13 pm, October 17, 2021
0 comments
0 likes
_I_ replied to Raise ground issues October 17, 2021 @ 10:10:09 am PDT
dig place stone slabs where the ground is not able to get to the height desired
5:13 pm, October 17, 2021
0 comments
0 likes